Need of Patent Drawings (Patent Cooperation Treaty) [PCT Article 7]

Need of drawings (Patent Cooperation Treaty) [PCT Article 7]

  1. Subject to the provisions, drawings shall be required when they are necessary for the understanding of the invention.
  2. Where, without being necessary for the understanding of the invention, the nature of the invention admits of illustration by drawings:

(i)  the applicant may include such drawings in the international application when filed,

(ii)  any designated Office may require that the applicant file such drawings with it within the prescribed time limit.

Flow Sheets and Diagrams []

Flow sheets and diagrams are considered drawings.

Time Limit

The time limit referred to in Article 7(2)(ii) shall be reasonable under the circumstances of the case and shall, in no case, be shorter than two months from the date of the written invitation requiring the filing of drawings or additional drawings under the said provision.

PCT Rule 11
Physical Requirements of the International Application

Size of Sheets

The size of the sheets shall be A4 (29.7 cm x 21 cm). However, any receiving Office may accept international applications on sheets of other sizes provided that the record copy, as transmitted to the International Bureau, and, if the competent International Searching Authority so desires, the search copy, shall be of A4 size.

Margins
(c) On sheets containing drawings, the surface usable shall not exceed 26.2 cm x 17.0 cm. The sheets shall not contain frames around the usable or used surface. The minimum margins shall be as follows:
– Top: 2.5 Cm
– Left Side: 2.5 Cm
– Right Side: 1.5 Cm
– Bottom: 1.0 Cm

Words in Drawings

(a) The drawings shall not contain text matter, except a single word or words, when absolutely indispensable, such as “water,” “steam,” “open,” “closed,” “section on AB,” and, in the case of electric circuits and block schematic or flow sheet diagrams, a few short catchwords indispensable for understanding.

(b) Any words used shall be so placed that, if translated, they may be pasted over without interfering with any lines of the drawings.

Special Requirements for Drawings

(a) Drawings shall be executed in durable, black, sufficiently dense, and dark, uniformly thick and well-defined, lines and strokes without colorings.

(b) Cross-sections shall be indicated by oblique hatching which should not impede the clear reading of the reference signs and leading lines.

(c) The scale of the drawings and the distinctness of their graphical execution shall be such that a photographic reproduction with a linear reduction in size to two-thirds would enable all details to be distinguished without difficulty.

(d) When, in exceptional cases, the scale is given on a drawing, it shall be represented graphically.

(e) All numbers, letters and reference lines, appearing on the drawings, shall be simple and clear. Brackets, circles or inverted commas shall not be used in association with numbers and letters.

(f) All lines in the drawings shall, ordinarily, be drawn with the aid of drafting instruments.

(g) Each element of each figure shall be in proper proportion to each of the other elements in the figure, except where the use of a different proportion is indispensable for the clarity of the figure.

(h) The height of the numbers and letters shall not be less than 0.32 cm. For the lettering of drawings, the Latin and, where customary, the Greek alphabets shall be used.

(i) The same sheet of drawings may contain several figures. Where figures on two or more sheets form in effect a single complete figure, the figures on the several sheets shall be so arranged that the complete figure can be assembled without concealing any part of any of the figures appearing on the various sheets.

(j) The different figures shall be arranged on a sheet or sheets without wasting space, preferably in an upright position, clearly separated from one another. Where the figures are not arranged in an upright position, they shall be presented sideways with the top of the figures at the left side of the sheet.

(k) The different figures shall be numbered in Arabic numerals consecutively and independently of the numbering of the sheets.

(l) Reference signs not mentioned in the description shall not appear in the drawings, and vice versa.

(m) The same features, when denoted by reference signs, shall, throughout the international application, be denoted by the same signs.

(n) If the drawings contain a large number of reference signs, it is strongly recommended to attach a separate sheet listing all reference signs and the features denoted by them.

CFR 1.437 The drawings.

  • (a) Drawings are required when they are necessary for the understanding of the invention (PCT Art. 7).
  • (b) The physical requirements for drawings are set forth in PCT Rule 11and shall be adhered to.

The international application must contain drawings when they are necessary for the understanding of the invention. Moreover where, without drawings being actually necessary for the understanding of the invention, its nature admits of illustration by drawings, the applicant may include such drawings and any designated Office may require the applicant to file such drawings during the national phase. Flow sheets and diagrams are considered drawings.

Drawings must be presented on one or more separate sheets. They may not be included in the description, the claims or the abstract. They may not contain text matter, except a single word or words when absolutely indispensable. Note that if the drawings contain text matter not in English but in a language accepted under PCT Rule 12.1(a) by the International Bureau as a Receiving Office, the international application will be transmitted to the International Bureau for processing in its capacity as a Receiving Office. See 37 CFR 1.412(c)(6)(ii). If the drawings contain text matter not in a language accepted under PCT Rule 12.1(a) by the International Bureau as a Receiving Office, the application will be denied an international filing date.

All lines in the drawings must, ordinarily, be drawn with the aid of a drafting instrument and must be executed in black, uniformly thick and well-defined lines. Color drawings are not acceptable. PCT Rules 11.10 to 11.13 contain detailed requirements as to further physical requirements of drawings. Drawings newly executed according to national standards may not be required during the national phase if the drawings filed with the international application comply with PCT Rule 11. The examiner may require new drawings where the drawings which were accepted during the international phase did not comply with PCT Rule 11. A file reference may be indicated in the upper left corner on each sheet of the drawings.

All of the figures constituting the drawings must be grouped together on a sheet or sheets without waste of space, preferably in an upright position and clearly separated from each other. Where the drawings cannot be presented satisfactorily in an upright position, they may be placed sideways, with the tops of the drawings on the left-hand side of the sheet.

The usable surface of sheets (which must be of A4 size) must not exceed 26.2 cm x 17.0 cm. The sheets must not contain frames around the usable surface. The minimum margins which must be observed are: top and left side: 2.5 cm; right side: 1.5 cm; bottom: 1.0 cm.

All sheets of drawings must be numbered in the center of either the top or the bottom of each sheet but not in the margin in numbers larger than those used as reference signs in order to avoid confusion with the latter. For drawings, a separate series of page numbers is to be used. The number of each sheet of the drawings must consist of two Arabic numerals separated by an oblique stroke, the first being the sheet number and the second being the total number of sheets of drawings. For example, “2/5” would be used for the second sheet of drawings where there are five in all.

Different figures on the sheets of drawings must be numbered in Arabic numerals consecutively and independently of the numbering of the sheets and, if possible, in the order in which they appear. This numbering should be preceded by the expression “Fig.”

In situations where one or more sheets are added, each sheet shall be identified by the number of the preceding sheet followed by a slant and then by another Arabic numeral such that the additional sheets are numbered consecutively, starting always with number one for the first sheet added after an unchanged sheet (e.g., 10/1, 15/1, 15/2, 15/3, etc.). See Administrative Instructions Section 311.

The PCT makes no provision for photographs. Nevertheless, they are allowed by the International Bureau where it is impossible to present in a drawing what is to be shown (for instance, crystalline structures). Where, exceptionally, photographs are submitted, they must be on sheets of A4 size, they must be black and white, and they must respect the minimum margins and admit of direct reproduction. Color photographs are not accepted.

The procedure for rectification of obvious mistakes in the drawings is explained in MPEP § 1836. The omission of an entire sheet of drawings cannot be rectified without affecting the international filing date, except in applications filed on or after April 1, 2007, where, if the application, on its initial receipt date, contained a priority claim and a proper incorporation by reference statement, the original international filing date may be retained if the submitted correction was completely contained in the earlier application. See PCT Rules 4.18 and 20.6. Rectifications of obvious mistakes are not considered to be amendments.

The drawings can be amended during the international phase only if the applicant files a Demand for international preliminary examination. The drawings can also be amended during the national phase. The amendment shall not go beyond the disclosure in the international application as filed. See PCT Article 34(2)(b).

If drawings are referred to in an international application and are not found in the search copy file, the examiner should refer the application to a Quality Assurance Specialist in his or her Technology Center or a PCT Special Program Examiner. See Administrative Instructions Section 310.

THE DRAWINGS

1.81 Drawings required in patent application.

[Editor Note: Para. (a) below is applicable only to patent applications filed under 35 U.S.C. 111 on or after December 18, 2013 *]

  • (a) The applicant for a patent is required to furnish a drawing of the invention where necessary for the understanding of the subject matter sought to be patented. Since corrections are the responsibility of the applicant, the original drawing(s) should be retained by the applicant for any necessary future correction.
  • (b) Drawings may include illustrations which facilitate an understanding of the invention (for example, flow sheets in cases of processes, and diagrammatic views).
  • (c) Whenever the nature of the subject matter sought to be patented admits of illustration by a drawing without its being necessary for the understanding of the subject matter and the applicant has not furnished such a drawing, the examiner will require its submission within a time period of not less than two months from the date of the sending of a notice thereof.
  • (d) Drawings submitted after the filing date of the application may not be used to overcome any insufficiency of the specification due to lack of an enabling disclosure or otherwise inadequate disclosure therein, or to supplement the original disclosure thereof for the purpose of interpretation of the scope of any claim.

[43 FR 4015, Jan. 31, 1978; para. (a), 53 FR 47809, Nov. 28, 1988, effective Jan. 1, 1989; para. (a) revised, 77 FR 48776, Aug. 14, 2012, effective Sept. 16, 2012; para. (a) revised, 78 FR 62368, Oct. 21, 2013, effective Dec. 18, 2013]

* Para. (a) above is only applicable to applications filed under 35 U.S.C. 111 on or after Dec. 18, 2013. See § 1.81 (2012‑09‑16 thru 2013‑12‑17) for para. (a) applicable to applications filed under 35 U.S.C. 111(a) or 363 on or after Sept. 16, 2012 and before Dec. 18, 2013. See § 1.81 (pre‑AIA) for para. (a) applicable to applications filed before Sept. 16, 2012.]

[top]

1.81 (2012‑09‑16 thru 2013‑12‑17) Drawings required in patent application.

[Editor Note: Para. (a) below is applicable to patent applications filed on or after September 16, 2012 and before December 18, 2013.]

  • (a) The applicant for a patent is required to furnish a drawing of the invention where necessary for the understanding of the subject matter sought to be patented; this drawing, or a high quality copy thereof, must be filed with the application. Since corrections are the responsibility of the applicant, the original drawing(s) should be retained by the applicant for any necessary future correction.
  • *****

[* Para. (a) above is applicable to applications filed under 35 U.S.C. 111 or 363 on or after Sept. 16, 2012 and before Dec. 18, 2013. See § 1.81 for the current rule, including para. (a) applicable to applications filed under 35 U.S.C. 111 on or after Dec. 18, 2013. See § 1.81 (pre‑AIA) for para. (a) applicable to applications filed before Sept. 16, 2012.]

 

1.81 (pre‑AIA) Drawings required in patent application.

[Editor Note: Para. (a) below is applicable to patent applications filed before September 16, 2012 *]

  • (a) The applicant for a patent is required to furnish a drawing of his or her invention where necessary for the understanding of the subject matter sought to be patented; this drawing, or a high-quality copy thereof, must be filed with the application. Since corrections are the responsibility of the applicant, the original drawing(s) should be retained by the applicant for any necessary future correction.
  • *****

[ * Para. (a) above is applicable to applications filed before Sept. 16, 2012. See § 1.81 for the current rule including para. (a) applicable to applications filed under 35 U.S.C. 111 on or after Dec. 18, 2013. See § 1.81 (2012‑09‑16 thru 2013‑12‑17) for para. (a) applicable to applications filed under 35 U.S.C. 111(a) or 363 on or after Sept. 16, 2012 and before Dec. 18, 2013. ]

[top]

1.83 Content of drawing.

  • (a) The drawing in a nonprovisional application must show every feature of the invention specified in the claims. However, conventional features disclosed in the description and claims, where their detailed illustration is not essential for a proper understanding of the invention, should be illustrated in the drawing in the form of a graphical drawing symbol or a labeled representation ( g.,a labeled rectangular box). In addition, tables that are included in the specification and sequences that are included in sequence listings should not be duplicated in the drawings.
  • (b) When the invention consists of an improvement on an old machine the drawing must when possible exhibit, in one or more views, the improved portion itself, disconnected from the old structure, and also in another view, so much only of the old structure as will suffice to show the connection of the invention therewith.
  • (c) Where the drawings in a nonprovisional application do not comply with the requirements of paragraphs (a) and (b) of this section, the examiner shall require such additional illustration within a time period of not less than two months from the date of the sending of a notice thereof. Such corrections are subject to the requirements of § 81(d).

[31 FR 12923, Oct. 4, 1966; 43 FR 4015, Jan. 31, 1978; paras. (a) and (c) revised, 60 FR 20195, Apr. 25, 1995, effective June 8, 1995; para. (a) revised, 69 FR 56481, Sept. 21, 2004, effective Oct. 21, 2004; para. (a) revised, 78 FR 62368, Oct. 21, 2013, effective Dec. 18, 2013]

[top]

1.84 Standards for drawings.

  • (a) There are two acceptable categories for presenting drawings in utility and design patent applications.
    • (1) Black ink.Black and white drawings are normally required. India ink, or its equivalent that secures solid black lines, must be used for drawings; or
    • (2) Color drawings are permitted in design applications. Where a design application contains color drawings, the application must include the number of sets of color drawings required by paragraph (a)(2)(ii) of this section and the specification must contain the reference required by paragraph (a)(2)(iii) of this section. On rare occasions, color drawings may be necessary as the only practical medium by which to disclose the subject matter sought to be patented in a utility patent application. The color drawings must be of sufficient quality such that all details in the drawings are reproducible in black and white in the printed patent. Color drawings are not permitted in international applications (see PCT Rule 11.13). The Office will accept color drawings in utility patent applications only after granting a petition filed under this paragraph explaining why the color drawings are necessary. Any such petition must include the following:
      • (i) The fee set forth in § 17(h);
      • (ii) One (1) set of color drawings if submitted via the Office electronic filing system or three (3) sets of color drawings if not submitted via the Office electronic filing system; and
      • (iii) An amendment to the specification to insert (unless the specification contains or has been previously amended to contain) the following language as the first paragraph of the brief description of the drawings:

The patent or application file contains at least one drawing executed in color. Copies of this patent or patent application publication with color drawing(s) will be provided by the Office upon request and payment of the necessary fee.

  • (b) —
    • (1) Black and white.Photographs, including photocopies of photographs, are not ordinarily permitted in utility and design patent applications. The Office will accept photographs in utility and design patent applications, however, if photographs are the only practicable medium for illustrating the claimed invention. For example, photographs or photomicrographs of: electrophoresis gels, blots ( g., immunological, western, Southern, and northern), autoradiographs, cell cultures (stained and unstained), histological tissue cross sections (stained and unstained), animals, plants, in vivo imaging, thin layer chromatography plates, crystalline structures, and, in a design patent application, ornamental effects, are acceptable. If the subject matter of the application admits of illustration by a drawing, the examiner may require a drawing in place of the photograph. The photographs must be of sufficient quality so that all details in the photographs are reproducible in the printed patent.
    • (2) Color photographs. Color photographs will be accepted in utility and design patent applications if the conditions for accepting color drawings and black and white photographs have been satisfied. See paragraphs (a)(2) and (b)(1) of this section.
  • (c) Identification of drawings. Identifying indicia should be provided, and if provided, should include the title of the invention, inventor’s name, and application number, or docket number (if any) if an application number has not been assigned to the application. If this information is provided, it must be placed on the front of each sheet within the top margin. Each drawing sheet submitted after the filing date of an application must be identified as either “Replacement Sheet” or “New Sheet” pursuant to § 121(d) . If a marked-up copy of any amended drawing figure including annotations indicating the changes made is filed, such marked-up copy must be clearly labeled as “Annotated Sheet” pursuant to § 1.121(d)(1) .
  • (d) Graphic forms in drawings. Chemical or mathematical formulae, tables, and waveforms may be submitted as drawings, and are subject to the same requirements as drawings. Each chemical or mathematical formula must be labeled as a separate figure, using brackets when necessary, to show that information is properly integrated. Each group of waveforms must be presented as a single figure, using a common vertical axis with time extending along the horizontal axis. Each individual waveform discussed in the specification must be identified with a separate letter designation adjacent to the vertical axis.
  • (e) Type of paper. Drawings submitted to the Office must be made on paper which is flexible, strong, white, smooth, non-shiny, and durable. All sheets must be reasonably free from cracks, creases, and folds. Only one side of the sheet may be used for the drawing. Each sheet must be reasonably free from erasures and must be free from alterations, over writings, and interlineations. Photographs must be developed on paper meeting the sheet-size requirements of paragraph (f) of this section and the margin requirements of paragraph (g) of this section. See paragraph (b) of this section for other requirements for photographs.
  • (f) Size of paper. All drawing sheets in an application must be the same size. One of the shorter sides of the sheet is regarded as its top. The size of the sheets on which drawings are made must be:
    • (1) 21.0 cm. by 29.7 cm. (DIN size A4), or
    • (2) 21.6 cm. by 27.9 cm. (8 1/2 by 11 inches).
  • (g) The sheets must not contain frames around the sight ( i.e., the usable surface), but should have scan target points ( i.e., cross-hairs) printed on two catercorner margin corners. Each sheet must include a top margin of at least 2.5 cm. (1 inch), a left side margin of at least 2.5 cm. (1 inch), a right side margin of at least 1.5 cm. (5/8 inch), and a bottom margin of at least 1.0 cm. (3/8 inch), thereby leaving a sight no greater than 17.0 cm. by 26.2 cm. on 21.0 cm. by 29.7 cm. (DIN size A4) drawing sheets, and a sight no greater than 17.6 cm. by 24.4 cm. (6 15/16 by 9 5/8 inches) on 21.6 cm. by 27.9 cm. (8 1/2 by 11 inch) drawing sheets.
  • (h) The drawing must contain as many views as necessary to show the invention. The views may be plan, elevation, section, or perspective views. Detail views of portions of elements, on a larger scale if necessary, may also be used. All views of the drawing must be grouped together and arranged on the sheet(s) without wasting space, preferably in an upright position, clearly separated from one another, and must not be included in the sheets containing the specifications, claims, or abstract. Views must not be connected by projection lines and must not contain center lines. Waveforms of electrical signals may be connected by dashed lines to show the relative timing of the waveforms.
    • (1) Exploded views. Exploded views, with the separated parts embraced by a bracket, to show the relationship or order of assembly of various parts are permissible. When an exploded view is shown in a figure which is on the same sheet as another figure, the exploded view should be placed in brackets.
    • (2) Partial views. When necessary, a view of a large machine or device in its entirety may be broken into partial views on a single sheet, or extended over several sheets if there is no loss in facility of understanding the view. Partial views drawn on separate sheets must always be capable of being linked edge to edge so that no partial view contains parts of another partial view. A smaller scale view should be included showing the whole formed by the partial views and indicating the positions of the parts shown. When a portion of a view is enlarged for magnification purposes, the view and the enlarged view must each be labeled as separate views.
      • (i) Where views on two or more sheets form, in effect, a single complete view, the views on the several sheets must be so arranged that the complete figure can be assembled without concealing any part of any of the views appearing on the various sheets.
      • (ii) A very long view may be divided into several parts placed one above the other on a single sheet. However, the relationship between the different parts must be clear and unambiguous.
    • (3) Sectional views. The plane upon which a sectional view is taken should be indicated on the view from which the section is cut by a broken line. The ends of the broken line should be designated by Arabic or Roman numerals corresponding to the view number of the sectional view, and should have arrows to indicate the direction of sight. Hatching must be used to indicate section portions of an object, and must be made by regularly spaced oblique parallel lines spaced sufficiently apart to enable the lines to be distinguished without difficulty. Hatching should not impede the clear reading of the reference characters and lead lines. If it is not possible to place reference characters outside the hatched area, the hatching may be broken off wherever reference characters are inserted. Hatching must be at a substantial angle to the surrounding axes or principal lines, preferably 45°. A cross section must be set out and drawn to show all of the materials as they are shown in the view from which the cross section was taken. The parts in cross section must show proper material(s) by hatching with regularly spaced parallel oblique strokes, the space between strokes being chosen on the basis of the total area to be hatched. The various parts of a cross section of the same item should be hatched in the same manner and should accurately and graphically indicate the nature of the material(s) that is illustrated in cross section. The hatching of juxtaposed different elements must be angled in a different way. In the case of large areas, hatching may be confined to an edging drawn around the entire inside of the outline of the area to be hatched. Different types of hatching should have different conventional meanings as regards the nature of a material seen in cross section.
    • (4) Alternate position. A moved position may be shown by a broken line superimposed upon a suitable view if this can be done without crowding; otherwise, a separate view must be used for this purpose.
    • (5) Modified forms. Modified forms of construction must be shown in separate views.
  • (i) Arrangement of views. One view must not be placed upon another or within the outline of another. All views on the same sheet should stand in the same direction and, if possible, stand so that they can be read with the sheet held in an upright position. If views wider than the width of the sheet are necessary for the clearest illustration of the invention, the sheet may be turned on its side so that the top of the sheet, with the appropriate top margin to be used as the heading space, is on the right-hand side. Words must appear in a horizontal, left-to-right fashion when the page is either upright or turned so that the top becomes the right side, except for graphs utilizing standard scientific convention to denote the axis of abscissas (of X) and the axis of ordinates (of Y).
  • (j) Front page view. The drawing must contain as many views as necessary to show the invention. One of the views should be suitable for inclusion on the front page of the patent application publication and patent as the illustration of the invention. Views must not be connected by projection lines and must not contain center lines. Applicant may suggest a single view (by figure number) for inclusion on the front page of the patent application publication and patent.
  • (k) The scale to which a drawing is made must be large enough to show the mechanism without crowding when the drawing is reduced in size to two-thirds in reproduction. Indications such as “actual size” or “scale 1/2” on the drawings are not permitted since these lose their meaning with reproduction in a different format.
  • (l) Character of lines, numbers, and letters. All drawings must be made by a process which will give them satisfactory reproduction characteristics. Every line, number, and letter must be durable, clean, black (except for color drawings), sufficiently dense and dark, and uniformly thick and well-defined. The weight of all lines and letters must be heavy enough to permit adequate reproduction. This requirement applies to all lines however fine, to shading, and to lines representing cut surfaces in sectional views. Lines and strokes of different thicknesses may be used in the same drawing where different thicknesses have a different meaning.
  • (m) The use of shading in views is encouraged if it aids in understanding the invention and if it does not reduce legibility. Shading is used to indicate the surface or shape of spherical, cylindrical, and conical elements of an object. Flat parts may also be lightly shaded. Such shading is preferred in the case of parts shown in perspective, but not for cross sections. See paragraph (h)(3) of this section. Spaced lines for shading are preferred. These lines must be thin, as few in number as practicable, and they must contrast with the rest of the drawings. As a substitute for shading, heavy lines on the shade side of objects can be used except where they superimpose on each other or obscure reference characters. Light should come from the upper left corner at an angle of 45°. Surface delineations should preferably be shown by proper shading. Solid black shading areas are not permitted, except when used to represent bar graphs or color.
  • (n) Graphical drawing symbols may be used for conventional elements when appropriate. The elements for which such symbols and labeled representations are used must be adequately identified in the specification. Known devices should be illustrated by symbols which have a universally recognized conventional meaning and are generally accepted in the art. Other symbols which are not universally recognized may be used, subject to approval by the Office, if they are not likely to be confused with existing conventional symbols, and if they are readily identifiable.
  • (o) Suitable descriptive legends may be used subject to approval by the Office, or may be required by the examiner where necessary for understanding of the drawing. They should contain as few words as possible.
  • (p) Numbers, letters, and reference characters.
    • (1) Reference characters (numerals are preferred), sheet numbers, and view numbers must be plain and legible, and must not be used in association with brackets or inverted commas, or enclosed within outlines, g.,encircled. They must be oriented in the same direction as the view so as to avoid having to rotate the sheet. Reference characters should be arranged to follow the profile of the object depicted.
    • (2) The English alphabet must be used for letters, except where another alphabet is customarily used, such as the Greek alphabet to indicate angles, wavelengths, and mathematical formulas.
    • (3) Numbers, letters, and reference characters must measure at least .32 cm. (1/8 inch) in height. They should not be placed in the drawing so as to interfere with its comprehension. Therefore, they should not cross or mingle with the lines. They should not be placed upon hatched or shaded surfaces. When necessary, such as indicating a surface or cross section, a reference character may be underlined and a blank space may be left in the hatching or shading where the character occurs so that it appears distinct.
    • (4) The same part of an invention appearing in more than one view of the drawing must always be designated by the same reference character, and the same reference character must never be used to designate different parts.
    • (5) Reference characters not mentioned in the description shall not appear in the drawings. Reference characters mentioned in the description must appear in the drawings.
  • (q) Lead lines.Lead lines are those lines between the reference characters and the details referred to. Such lines may be straight or curved and should be as short as possible. They must originate in the immediate proximity of the reference character and extend to the feature indicated. Lead lines must not cross each other. Lead lines are required for each reference character except for those which indicate the surface or cross section on which they are placed. Such a reference character must be underlined to make it clear that a lead line has not been left out by mistake. Lead lines must be executed in the same way as lines in the drawing. See paragraph (l) of this section.
  • (r) Arrows may be used at the ends of the lines, provided that their meaning is clear, as follows:
    • (1) On a lead line, a freestanding arrow to indicate the entire section towards which it points;
    • (2) On a lead line, an arrow touching a line to indicate the surface shown by the line looking along the direction of the arrow; or
    • (3) To show the direction of movement.
  • (s) Copyright or Mask Work Notice. A copyright or mask work notice may appear in the drawing, but must be placed within the sight of the drawing immediately below the figure representing the copyright or mask work material and be limited to letters having a print size of .32 cm. to .64 cm. (1/8 to 1/4 inches) high. The content of the notice must be limited to only those elements provided for by law. For example, “©1983 John Doe” (17 U.S.C. 401) and “*M* John Doe” (17 U.S.C. 909) would be properly limited and, under current statutes, legally sufficient notices of copyright and mask work, respectively. Inclusion of a copyright or mask work notice will be permitted only if the authorization language set forth in § 71(e) is included at the beginning (preferably as the first paragraph) of the specification.
  • (t) Numbering of sheets of drawings. The sheets of drawings should be numbered in consecutive Arabic numerals, starting with 1, within the sight as defined in paragraph (g) of this section. These numbers, if present, must be placed in the middle of the top of the sheet, but not in the margin. The numbers can be placed on the right-hand side if the drawing extends too close to the middle of the top edge of the usable surface. The drawing sheet numbering must be clear and larger than the numbers used as reference characters to avoid confusion. The number of each sheet should be shown by two Arabic numerals placed on either side of an oblique line, with the first being the sheet number and the second being the total number of sheets of drawings, with no other marking.
  • (u) Numbering of views.
    • (1) The different views must be numbered in consecutive Arabic numerals, starting with 1, independent of the numbering of the sheets and, if possible, in the order in which they appear on the drawing sheet(s). Partial views intended to form one complete view, on one or several sheets, must be identified by the same number followed by a capital letter. View numbers must be preceded by the abbreviation “FIG.” Where only a single view is used in an application to illustrate the claimed invention, it must not be numbered and the abbreviation “FIG.” must not appear.
    • (2) Numbers and letters identifying the views must be simple and clear and must not be used in association with brackets, circles, or inverted commas. The view numbers must be larger than the numbers used for reference characters.
  • (v) Security markings. Authorized security markings may be placed on the drawings provided they are outside the sight, preferably centered in the top margin.
  • (w) Any corrections on drawings submitted to the Office must be durable and permanent.
  • (x) No holes should be made by applicant in the drawing sheets.
  • (y) Types of drawings. See § 152 for design drawings, § 1.1026 for international design reproductions, § 1.165 for plant drawings, and § 1.173(a)(2) for reissue drawings.

[24 FR 10332, Dec. 22, 1959; 31 FR 12923, Oct. 4, 1966; 36 FR 9775, May 28, 1971; 43 FR 20464, May 11, 1978; 45 FR 73657, Nov. 6,1980; paras. (a), (b), (i), (j), and (l) amended, paras. (n), (o), and (p) added, 53 FR 47809, Nov. 28, 1988, effective Jan. 1, 1989; revised, 58 FR 38719, July 20, 1993, effective Oct. 1, 1993; paras. (c), (f), (g), and (x) revised, 61 FR 42790, Aug. 19, 1996, effective Sept. 23, 1996; paras. (a)(2)(i), (b), (c) & (g) revised, 62 FR 53132, Oct. 10, 1997, effective Dec. 1, 1997; paras. (a), (b), (c), (j), (k), (o), and (x) revised, and para. (y) added, 65 FR 54604, Sept. 8, 2000, effective Nov. 7, 2000; paras. (a)(2), (e), and (j) revised, 65 FR 57024, Sept. 20, 2000, effective Nov. 29, 2000; para. (c) revised, 69 FR 56481, Sept. 21, 2004, effective Sept. 21, 2004; para. (a)(2) revised, 69 FR 56481, Sept. 21, 2004, effective Nov. 22, 2004; para. (y) revised, 70 FR 3880, Jan. 27, 2005, effective Dec. 8, 2004; para.(a)(2) introductory text revised, 78 FR 11024, Feb. 14, 2013, effective Mar. 16, 2013; paras. (a)(2) and (y) revised, 80 FR 17918, Apr. 2, 2015, effective May 13, 2015]

[top]

1.85 Corrections to drawings.

  • (a) A utility or plant application will not be placed on the files for examination until objections to the drawings have been corrected. Except as provided in § 215(c), any patent application publication will not include drawings filed after the application has been placed on the files for examination. Unless applicant is otherwise notified in an Office action, objections to the drawings in a utility or plant application will not be held in abeyance, and a request to hold objections to the drawings in abeyance will not be considered a bona fide attempt to advance the application to final action (§ 1.135(c) ). If a drawing in a design application meets the requirements of § 1.84(e), (f), and (g) and is suitable for reproduction, but is not otherwise in compliance with § 1.84 , the drawing may be admitted for examination.
  • (b) The Office will not release drawings for purposes of correction. If corrections are necessary, new corrected drawings must be submitted within the time set by the Office.
  • (c) If a corrected drawing is required or if a drawing does not comply with § 84or an amended drawing submitted under § 1.121(d) in a nonprovisional international design application does not comply with § 1.1026 at the time an application is allowed, the Office may notify the applicant in a notice of allowability and set a three-month period of time from the mail date of the notice of allowability within which the applicant must file a corrected drawing in compliance with § 1.84 or 1.1026 , as applicable, to avoid abandonment. This time period is not extendable under § 1.136 (see § 1.136(c) ).
Scroll to Top